By industry

Piezoresistive pressure transmitter – Series 23(S)Y / 25Y

The Series 23SY / 25Y product line is outstanding due to its extreme ruggedness towards electromagnetic fields. The limits of the CE standard are undercut by a factor of up to 10 with conducted and radiated fields.

• Series 23SY Ranges 0,1…1000 bar Fully welded (no internal seals)
• Series 25Y Ranges 0,5…1000 bar Flush, fully welded...

Piezoresistive pressure transmitter – Serie 21Y

The 21Y product line is outstanding due to its extreme ruggedness towards electromagnetic fields. The 21Y product line is outstanding due to its extreme ruggedness towards electromagnetic fields....

Immersion temperature probe – STI

This type of sensor is ideally suited for oil measurements, such as engine oil or other fluids within the limits of the RTD type sensing element. This model meets the requirements of MILSTD-810F. Its fast response time and good accuracy make it an ideal sensor for accurate measurements in harsh environments. A transmitter with an analog output (voltage or current) is integrated inside the body. The 316L stainless steel body and the laser welding between the body and the connector ensure an unma...

Atmosphere temperature probe- STA

This model of temperature sensor exists in PT100 platinum probe version or in thermocouple version. It is ideal for ambient temperature measurements. This range of sensors is equipped with a shielded Teflon extension cable and a support plate for fixing...

ICP single-axis accelerometer – Serie CMCP1100

The CMCP1100 100 mV/g accelerometer with integral 5, 10 or 20 meter cable is manufactured to high quality standards. Each accelerometer is sealed in a waterproof stainless steel case....

Position rotating sensor – Serie PS

PS-range sensors are designed to measure angle displacements over 340° to 350°. They can make different revolutions at the maximal rotating speed of 600 rev/min. They include a potentiometric plastic track.

• Separate linearity: ± 0,05% (standard is ± 0,5%).
• Infinite resolution.
• Repeatability: 0.01 of the CET.
• Rotating speed up to
• Lifespan > 100x106 operations at 10 rev/s.
• Protection class: IP 40.

1/2/3-axis inclinometer – Serie ME26400 BOX - Serie ME26400 BOX

• Measurement of angle on 1/2/3 axes.
• Measurement range: ± 10, 30, 70, 80, 360°.
• Cast aluminium housing. Protection class: IP65.
• Analog output: 4-20 mA, 0-5 V, ± 5 V.
• •Zero and gain adjustable through potentiometers.

Potentiometric and magneto resistive displacement sensor – PY2

PY2-range sensors are designed to measure linear displacements from 0-10 mm to 100 mm. Three measurement ranges are available, all with a linearity ranging from 0.2 to 0.1%.
They feature a contact tip and a return spring and they include a potentiometric plastic track.

• Separate linearity up to ± 0,1%.
• Infinite resolution.
• Lifespan > 100x106 operations.
• Displacement speed up to 10 m/s.
• Protection class: IP40.

Potentiometric and magneto resistive displacement sensor- Serie PY3

PY3-range sensors are designed to measure linear displacements from 0-10 mm to 100 mm, with a linearity ranging from 0.3% to 0.1%. They feature a contact caster and a return spring and they include a single plastic track.

• Separate linearity up to ± 0,1%.
• Infinite resolution.
• Lifespan > 100x106 operations.
• Displacement speed up to 10 m/s.

Potentiometric and magneto resistive displacement sensor – Série LT

LT-range sensors are designed to measure linear displacements from 0-50 mm to 900 mm. Different measurement ranges are available, with a linearity ranging from 0.1% to 0.05%

• They include a potentiometric plastic track.
• Separate linearity up to 0.05%.
• Infinite resolution.
• Repeatability: 0,01 mm.
• Displacement speed up to 5 m/s (optional: 10 m/s).
• Lifespan > 100x106 operations.

Static torque meter – Serie CS2

General purpose, non-contact rotary torque sensors with square or round shaft.

• Bidirectional
• Integrated signal conditionning
• Analogue output signal
• Cable length: 5 m...

Incremental Encoders – ROD436

ROD 436 encoders are designed to measure angle displacements of rotating speeds.

• Two 90°-offset incremental encoders to perform the counting of both Ua1 and Ua2 angles.
• 1 Ua0 top zero.
• 1 UaS perturbation signal.
• As standard, they propose from 50 to 10,000 lines per revolution.

Static torque meter – Serie CS1

• Material: Stainless steel
• Protection class: IP97
• Low design
• Cost-effective solution
• Sturdy design
• Easy to install
• Whole range of mounting kits available
• Cable length: 6 m...

Static torque meter – Serie CS3

Universal non-rotating torque meters combining accuracy and sturdiness.

• Easy to install, compact design
• Protection class: iP65
• Materialstainless steel (61000), nickel-plated steel (6105)
• Cable length: 3m...

Cable displacement sensor – Serie CD 50

A linear CD50 works according to the principle of a thread taut between a mobile element and a fixed element, fitted with a return spring drum. The drum then converts the linear displacement into an angle displacement. The shaft of the drum is fitted with a potentiometer, and operates an incremental encoder or an absolute encoder....

1-axis inclinometer – Serie ME26400

• ME26410: ±10
• ME26430: ±30
• ME26480: ±80°

ME2657 - High accuracy programmable attenuator with analog and USB outputs (table set)

MEIRI 2657-ATT90 USB box offers analog electronics allowing to attenuate voltage signals until -90dB, with a ±0.1dB accuracy.
Attenuated signal input and output are made thought BNC connectors.
Programming attenuation is set up from the front panel or from a USB plug.
A dashboard on the PC screen enables to set up the attenuator. It can also be programmed by a DLL included with the equipment. Standard model “A” is supplied by mains, version “B” is supplied by rechargeabl...

2680C - Multichannel multifunction measuring unit

2680C measuring unit is able to condition from 4 to 16 sensors, with totally different sensor on each channel.
2680 control unit allows to set up acquisition channels configurations as gain, zero, offset… by sending digital commands handled through the control panel; or be set up with USB connection through a remote PC to acquire direct data and exploit them into Microsoft Excel for instance (.csv files)...